Custom 1060 Aluminum Textured Busbar Connector Link and T-Bracket Kit
Video
Short Description
A custom 1060 aluminum busbar connector kit comprising a long textured link and T-shaped mounting brackets. The pictured link has an annular raised feature with a central hole at one end, two holes along the textured section, and a formed stop at the opposite end.
The product notes identify 1060 electrical aluminum and describe the link and T-brackets as a matched set. Confirm the kit contents, material temper, dimensions, hole pattern, surface finish and acceptance criteria against the approved drawing and order requirements.
Product Description
This custom 1060 aluminum busbar connector kit is designed around a textured link and perpendicular T-bracket components. The link shown has a raised annular feature at one end, two through-holes along its length, and a formed end feature. The fourth photo shows two T-shaped brackets alongside the link; confirm whether all three components are included in the same orderable set.
The raised grid texture is visible on the mating faces, but its electrical or mechanical effect depends on the joint design and must be validated for the intended assembly. For material information, see ourAluminum Alloypage. Drawing-based processing requirements can be reviewed throughFine Machining.
Key Features
- Matched link-and-bracket configuration, subject to confirmation of the kit contents.
- Long link with a raised annular end feature, two intermediate holes and a formed stop feature.
- T-shaped brackets provide perpendicular mounting geometry.
- Raised grid-like surface texture is visible on the pictured contact faces.
- Material, component dimensions, hole layout and finish can be specified by drawing.
Typical Applications
| Application | Possible Use |
|---|---|
| Switchgear and Distribution Panels | Custom aluminum conductor link or mounting transition |
| Ring Main Units | Drawing-specific busbar connection components |
| Inverters and Power Conversion Equipment | Link-and-bracket arrangement within an electrical assembly |
| Energy Storage Equipment | Custom conductor connection, subject to electrical and mechanical review |
| Aluminum Busbar Assemblies | Link or support components configured to the assembly drawing |
Application suitability depends on the complete assembly, including current, temperature rise, contact design, fasteners, clearances, insulation and relevant equipment requirements. These details should be reviewed by the project engineer.
Typical Manufacturing Process
The process below is indicative. Confirm the actual production route, kit contents and finish against the drawing and order requirements.
| Step | Process | Details to Confirm |
|---|---|---|
| 1 | Material Review | Confirm 1060 grade, temper, standard and required material records |
| 2 | Link Preparation | Set link dimensions, annular feature and formed end geometry |
| 3 | Surface Texture | Define the grid pattern, coverage and forming or machining method |
| 4 | Bracket Processing | Confirm T-section geometry, hole layout and mounting interface |
| 5 | Hole Making and Finishing | Verify hole dimensions, edge condition, deburring and specified finish |
| 6 | Final Inspection and Packing | Inspect agreed features and protect contact faces during packing |
Manufacturing & Quality Control
| Control Point | Review Approach |
|---|---|
| Material | Verify grade and temper against the purchase specification and available material documentation |
| Link Geometry | Check length, width, thickness, annular feature, hole positions and formed end details |
| Bracket Geometry | Check T-profile, mounting dimensions, hole layout and fit with the link |
| Texture | Review pattern, location and surface condition against the drawing |
| Finish | Confirm coating or passivation specification and agreed inspection requirements |
| Assembly Validation | Contact resistance, temperature-rise or vibration tests only when specified and agreed for the complete joint |
| Documentation | Confirm required material records and inspection reports before order placement |
For inspection methods and available documentation, see ourQuality Assurancepage. Product-specific tests and acceptance criteria should be agreed before ordering.
Frequently Asked Questions
The product notes describe a textured aluminum link with matching T-brackets, and the fourth photo shows one link with two brackets. Confirm the orderable set contents and quantities before publication or quotation.
The supplied product notes identify the material as 1060 electrical aluminum. Confirm the temper, material standard and required documents for the specific order.
The photographs show a raised grid-like texture, but they do not establish its effect on slip or oxide layers. Joint performance depends on the mating materials, surface condition, fastener load and assembly design and should be validated for the application.
Dimensions and hole patterns should be specified on the drawing. The broad ranges listed in the product notes are reference values, not guaranteed dimensions for every component or kit.
The supplied notes mention tin, nickel or silver plating and conductive passivation. Confirm the required finish, aluminum pretreatment, coating thickness and compatibility with the mating parts before ordering.
It may be considered for a custom busbar assembly, but suitability depends on the equipment design and operating conditions. Confirm the current, temperature rise, joint resistance, clearances and applicable standards with the project engineer.
Provide the drawing, 1060 temper and standard, kit contents, link and bracket dimensions, hole details, tolerances, finish, quantity, application and required documentation.
RFQ Information
| Please Provide | Details |
|---|---|
| Material | 1060 grade, temper and material standard |
| Drawing | 2D or 3D drawing with critical dimensions and tolerances |
| Kit Contents | Number of links and brackets required |
| Link | Length, width, thickness, annular feature, holes and formed end details |
| Brackets | T-profile dimensions, hole layout and mounting interface |
| Surface | Grid texture requirements and specified coating or passivation |
| Application | Equipment type and relevant electrical or mechanical requirements |
| Quantity | Sample and production quantities |
| Documents | Material certificate, inspection report or other required records |
| Delivery | Destination country, packing requirements and target schedule |
Send your drawing and requirements throughContact Usfor material and manufacturing review.










