Custom Double-Sided Stepped Copper Profile
Video
Short Description
Custom double-sided stepped copper profile featuring a wide raised central pad, recessed side flanges and rear edge rebates. Supplied as profile bars, cut-to-length baseplate blanks or further-machined components, with material, step geometry, flatness, surface finish and inspection requirements specified to the approved drawing.
Product Overview
This double-sided stepped copper profile combines a broad central raised pad with lower side flanges and stepped edge features on the reverse face. The section provides different mounting or interface levels within a single copper profile.
Part of ourpure copper productsrange, it can be evaluated for power-module baseplate blanks, conductive mounting components, stepped busbars and cooling-assembly cover blanks.
The raised pad and edge rebates can be designed around mating parts, insulation openings or joining interfaces. Final suitability depends on the complete assembly, including thermal expansion, surface preparation, fastening or joining methods and operating conditions.
Key Features
- Raised central pad:Provides a defined interface area above the side flanges.
- Double-sided stepped geometry:Front and rear features can be coordinated with mating components.
- Custom edge rebates:Locating shoulders and relief details can be reviewed against the assembly drawing.
- Flexible supply forms:Specify longer profiles, cut blanks or machined components.
- Application-based finishing:Flatness, roughness and plating requirements can be defined for the intended interface.
Manufacturing & Quality Control
| Stage | Scope |
|---|---|
| Drawing Review | Confirm front and rear steps, datum surfaces, corner radii, machining allowances and mating clearances |
| Material Selection | Confirm copper grade, condition and composition requirements; specify suitable oxygen-content testing where required |
| Profile Production | Assesscustom copper profile extrusion, drawing and machining according to section geometry and quantity |
| Cutting & Finishing | Cut-to-length preparation, drilling, tapping and interface finishing through agreedcopper machining support |
| Surface Treatment | Confirm coating process, thickness, coverage, masking and final dimensional requirements |
| Final Inspection | Inspect agreed step dimensions, flatness, parallelism, surface condition and specified material properties |
| Packaging | Protect raised pads, flange edges and finished surfaces during handling and shipment |
Inspection methods, sampling plans and acceptance criteria are agreed before production. Refer to ourQuality Assurancepage for further information.
Typical Applications
| Application | Potential Use |
|---|---|
| IGBT and SiC Power Modules | Copper baseplate blanks subject to interface, joining and thermal-cycling review |
| Liquid-Cooling Assemblies | Stepped cover blanks or mounting interfaces requiring further processing and assembly validation |
| Switchgear and Busbar Systems | Conductive sections with locating shoulders or overlapping edge geometry |
| Inverters and Energy Storage Equipment | Custom thermal or electrical interface components |
| Rectifiers and Solid-State Relays | Copper mounting or heat-spreading baseplate blanks |
These are potential uses, not equipment approvals or guaranteed thermal, electrical or pressure ratings.
FAQ
It is a copper section with stepped features on both faces. This design combines a wide raised central pad, recessed side flanges and rear edge rebates. The individual dimensions are specified to suit the mating assembly.
C11000 ETP, C10200 oxygen-free and C10100 oxygen-free electronic copper may be considered. Selection depends on electrical and thermal requirements, joining conditions, material condition and the applicable standard. Grade and documentation requirements should be confirmed before production.
Yes. Pad width and height, flange thickness, rebate depth and feature positions can be reviewed against your drawing. Identify the datum surfaces and critical flatness, parallelism and step tolerances so the production route can be assessed.
The route depends on geometry, quantity, material condition and tolerances. Extrusion and drawing may be evaluated for suitable sections, while secondary machining may be needed for interface surfaces, holes or other features. The route is confirmed after drawing review.
It can be evaluated as a baseplate blank. Direct use requires confirmation of flatness, surface finish, coating, bonding method and thermal-expansion compatibility. The finished module must also meet its thermal-cycling and reliability requirements.
C10200 or C10100 may be considered where low oxygen content is important, particularly for joining in hydrogen-containing reducing atmospheres. Oxygen-free copper is not literally oxygen-free, and grade selection alone does not qualify a brazing process. Joint design and process validation remain necessary.
No pressure or leak rating is implied by the profile geometry. Leak tightness depends on the finished cooling assembly, including joints and seals. Pressure or leak testing should be specified for the relevant finished component with agreed acceptance criteria.
Nickel, silver or tin plating can be reviewed according to the application. Specify the coating process, thickness, masking and inspection requirements. Material certificates, dimensional reports and treatment records can be included in the agreed order scope.
Request a Quote
Please provide a cross-section drawing or CAD file showing both faces, together with the copper grade, material condition, required lengths and quantity.
Include critical step dimensions, flatness, parallelism, surface finish, machining and plating requirements. For cooling or power-module applications, also identify the joining process, interface requirements and any finished-assembly testing.
Contact Cymber Metal for a quotationwith your documentation requirements, delivery destination and target schedule.










