Slotted Copper Disconnector Contact Blade with Pivot Hole

Short Description:

Item Specification / Enquiry Reference
Product Type Slotted copper disconnector contact blade / moving contact arm
Main Geometry Flat body, split tip, rear pivot hole and projecting side lug
Material Options C11000, C10200 or C10100, subject to the purchase specification
Other Material Designations Cu-ETP, Cu-OF, T2, TU1 and TU2 can be reviewed against their applicable standards; equivalence is not assumed
Alternative Copper Alloys C10400, C10700 or C18150 may be reviewed separately where mechanical or thermal requirements justify a different material
Starting Material Standard ASTM B187/B187M, ASTM B152/B152M or an applicable EN standard, depending on starting form
Overall Length Reference range: 100–1,200 mm
Body Width Reference range: 15–120 mm
Thickness Reference range: 3–25 mm
Longitudinal Slot Width Reference range: 0.8–4 mm
Slot Length and End Geometry Defined by drawing and required mechanical behavior
Pivot and Drive Holes Diameters, locations, fits and bearing arrangements to drawing
Hole Fit Options H7 or H8 where specified; numerical limits depend on nominal diameter
Hole Center Distance Reference tolerance target: ±0.02–0.04 mm
Slot Symmetry Reference target: ≤0.03 mm relative to an agreed datum and inspection method
Flatness and Straightness Reference target: ≤0.05 mm over a specified 300 mm span, subject to review
Functional Surface Roughness Reference target: Ra 0.2–0.4 µm on designated contact or edge surfaces
Hardness Reference range: 95–130 HV for selected material conditions; final requirement to be agreed
Conductivity Grade- and condition-specific requirement, verified when included in the order
Contact-End Features Contact pads, inserts, dimples or recesses according to the drawing
Surface Treatment Cleaned copper; optional anti-tarnish treatment or specified silver, tin or nickel plating
Optional Silver Plating Reference thickness: 10–30 µm, with coverage and coating specification agreed
Electrical Ratings Defined and validated at equipment level
Documentation Material and inspection records according to the purchase order

Product Detail

Product Tags

Video

Short Description

This copper disconnector contact blade features a longitudinally slotted tip, a rear pivot hole and a side lug for a drawing-defined operating linkage. The flat conductive body can be customized in material, thickness, hole spacing, slot geometry and contact-end configuration. Optional contact-area plating and inspection requirements are reviewed for the intended disconnector or earthing-switch assembly.

Product Overview

A copper disconnector contact blade is a moving conductive component that engages a mating contact within a switching assembly. Its geometry must coordinate the electrical contact interface, pivot location and operating linkage.

The photographed component has a long flat body, a split tip with two circular end features, a larger rear hole and a smaller hole in a projecting side lug. The longitudinal slot passes through a circular opening near the tip and continues into the blade body. The precise functions of these features follow the assembly drawing.

Material selection can be reviewed within ourpure copper product range. C11000, C10200 and C10100 may be considered according to conductivity, material condition and subsequent processing requirements.

Ourcustom copper machining servicessupport enquiries for blade profiles, slots, pivot bores and contact-interface features. Contact force, operating life, temperature rise and short-circuit performance require validation in the intended assembly.

Key Features

Feature Product Detail / Design Consideration
Longitudinal Split Tip Divides the contact end into two sections; allowable deflection and contact force depend on the design
Flat Conductive Body Provides a drawing-defined current path between the contact end and rear connection
Rear Pivot Interface Hole diameter, fit, bearing length and surrounding geometry can be specified
Side Drive Lug Provides a location for a drawing-defined operating linkage
Custom Contact-End Geometry Circular contact features can be specified for the required mating arrangement
Rounded Profile Transitions Edge radii and transitions can be controlled for assembly clearance and surface requirements
Optional Contact-Area Plating Coating type, thickness and coverage can be selected for the contact specification
Drawing-Based Customization Length, thickness, slot configuration and hole spacing can be reviewed together

The presence of a slot does not by itself establish spring performance, constant contact pressure or resistance to contact welding.

Manufacturing Process

Stage Process / Control Focus
Drawing Review Confirm material, condition, blade profile, hole locations, slot geometry and contact requirements
Starting Material Selection Select suitable copper bar or plate with the required thickness and material documentation
Blank Preparation Prepare the blank with appropriate machining allowance and material identification
Condition and Distortion Review Plan machining and any thermal processing around residual stress and final hardness requirements
Profile Machining Produce the blade outline, side lug, rounded ends and specified transitions
Hole Machining Drill, bore or ream pivot and linkage holes according to their dimensional requirements
Precision Slotting Produce the longitudinal slot using a suitable milling or EDM process
Post-Slot Inspection Check slot width, tip alignment, flatness and distortion after material removal
Contact-Feature Processing Machine or install specified contact features according to the approved design
Edge Finishing Remove burrs and finish designated edges without altering critical dimensions
Optional Plating Apply the specified coating while accounting for final fits and contact geometry
Final Inspection and Packing Inspect ordered characteristics and protect contact surfaces and slender tip sections

Any stress-relief or annealing operation must be evaluated for its effect on final hardness and strength. A full-hard condition should not be assumed to remain unchanged after thermal processing.

For finishing context, see ourbusbar plating shop. Coating requirements for moving contacts require separate confirmation.

Manufacturing & Quality Control

Inspection Area Proposed Verification Acceptance Basis
Material Identity Review material documentation and agreed composition checks Selected grade and purchase specification
Material Condition Verify required condition and specified mechanical properties Approved material requirements
Overall Dimensions Measure length, width, thickness and profile Approved drawing
Pivot and Drive Holes Check diameter, fit and location using suitable equipment Drawing limits and datum scheme
Hole Center Distance Measure the relationship between pivot and linkage features Specified center distance and tolerance
Slot Geometry Inspect width, length, position and end configuration Approved slot dimensions
Split-Tip Alignment Check tip separation, relative position and distortion Drawing or agreed inspection fixture
Flatness and Straightness Measure over the specified span and support arrangement Drawing requirements
Contact Features Inspect position, geometry and attachment where applicable Approved contact design
Surface and Edge Condition Inspect for burrs, unacceptable damage and machining defects Agreed workmanship criteria
Surface Roughness Measure designated functional surfaces Specified Ra values and measurement conditions
Conductivity and Hardness Perform testing when required by the order Agreed material acceptance limits
Force and Deflection Test in a defined fixture when required Specified load, displacement and residual-set limits
Contact Performance Evaluate resistance, temperature rise or cycling where included Agreed test assembly and procedure
Plating Inspect specified thickness, coverage and other coating characteristics Approved coating specification
Documentation Provide agreed inspection and material records Purchase-order requirements

Hardness testing does not establish elastic modulus or fatigue life. These require appropriate material data and functional testing. Further information is available on ourquality assurance page.

Typical Applications

These are potential application areas, subject to equipment-specific design review and qualification.

Application Area Potential Component Role Requirements to Confirm
Three-Position Disconnectors Moving blade within an isolation and earthing arrangement Operating travel, contact engagement, interlocks and insulation clearances
Ring Main Units Drawing-specific moving contact arm Mating contacts, drive linkage, temperature rise and equipment qualification
Indoor Disconnectors Hinged conductive blade Pivot fit, contact pressure, alignment and operating endurance
Outdoor Disconnectors Custom moving blade or conductive arm Environmental exposure, corrosion protection and mechanical loads
Earthing Switches Conductive blade within a qualified earthing assembly Required making and withstand duties, contact retention and operating mechanism
Renewable-Energy and Rail Installations Contact component within project-specific disconnecting equipment Applicable equipment standard, current duty and installation conditions

A disconnector blade should not be described as capable of interrupting load or fault current unless that duty is established for the complete switching device.

Frequently Asked Questions

What is a copper disconnector contact blade?

A copper disconnector contact blade is a moving conductor that engages a mating contact in a disconnecting assembly. The blade geometry includes electrical and mechanical interfaces, such as the contact end, pivot and operating linkage. Its suitability depends on the complete equipment design.

What is the purpose of the longitudinal slot?

The slot divides the tip into two sections and can be used to adjust their mechanical compliance. Actual contact force and alignment behavior depend on slot length, section dimensions, material condition and the mating contact. These properties require calculation or testing rather than visual assessment alone.

Are the circular features at the tip silver contacts?

Their material cannot be confirmed from the photographs. They may represent contact features or insert locations defined by the drawing. If silver contacts or silver-alloy inserts are required, please specify composition, dimensions, attachment method and acceptance criteria separately from any surface plating.

Which copper grade should be selected?

C11000, C10200 and C10100 can be considered for conductive blade designs. The choice depends on conductivity, strength, processing and service conditions. Where repeated deflection or elevated-temperature strength is important, alternative copper alloys may be reviewed, with their different electrical and mechanical properties assessed.

Can the pivot hole and drive-lug position be customized?

Yes. Their geometry can be specified for drawing review. Please provide hole diameters, fit requirements, center distances, datums and mating-pin information. H7 and H8 designate size-dependent tolerance zones, not a universal ±0.015 mm tolerance.

Does a full-hard copper condition guarantee spring recovery?

No. Hardness or temper alone does not guarantee contact force, elastic recovery or fatigue life. These depend on material properties, geometry, stress, temperature and cycling. Where tip flexibility is functional, specify force-deflection requirements, allowable permanent set and endurance criteria.

Can the blade be silver plated?

Silver plating can be reviewed for designated contact areas or other specified surfaces. The coating specification should define thickness, coverage, any underlayer, hardness where relevant and final dimensional requirements. Plating alone does not guarantee resistance to welding or a particular operating life.

Is this blade independently certified to IEC 62271-102?

This listing does not establish independent certification or an electrical rating for the blade. IEC 62271-102 addresses relevant disconnector and earthing-switch equipment requirements. Compliance claims require the applicable equipment design, test evidence and documentation, not merely the component’s material or shape.

Request a Quote

Required Information Details to Provide
Drawing / CAD File Dimensioned PDF and STEP or other available CAD format
Material Grade, standard, condition and required properties
Main Dimensions Length, width, thickness and blade outline
Slot Requirements Width, length, position and end geometry
Hole Requirements Diameters, fits, center distances and datums
Contact Features Pad or insert geometry, material and attachment method
Mechanical Behavior Required force-deflection relationship, allowable permanent set and operating cycles
Electrical Conditions Continuous current, temperature-rise limits and applicable equipment duties
Surface Treatment Plating type, thickness, coverage and finish
Inspection Required tests, sampling, reports and material documentation
Quantity Prototype quantity, batch quantity and expected repeat demand
Delivery Destination and requested delivery schedule

Contact Cymber Metal for a drawing-based quotationwith your blade drawing, material specification and assembly requirements.


  • Previous:
  • Next:

  • Write your message here and send it to us