L-Bent Slotted Copper Busbar Connector

Short Description:

Item Reference Specification
Product Type L-bent slotted copper busbar connector
Photographed Configuration Four longitudinal through-slots forming five ribs across the bent section
Main Material Options C11000 ETP copper, C10200 oxygen-free copper, or C10100 oxygen-free electronic copper
Alternative Grade Designations Cu-ETP, Cu-OF, T2, TU1 or TU2, subject to the specified standard and grade verification
Long Arm Reference Range 60–450 mm
Short Arm Reference Range 30–250 mm
Body Width Reference Range 30–220 mm
Body Thickness Reference Range 6–40 mm
Slot Configuration Four slots shown; alternative slot counts and layouts subject to engineering review
Slot Width Reference Range 2–12 mm
Slot Width / Rib Thickness Tolerance Reference requirement: ±0.03–0.05 mm on designated features
Mounting Hole Position Reference requirement: ±0.02 mm relative to agreed drawing datums
Bend Angle Nominal 90° or a drawing-defined alternative
Bend Angle Tolerance Reference requirement: ±0.2°
Contact Pad Flatness Reference requirement: 0.02–0.03 mm over the specified contact area
Contact Surface Roughness Reference requirement: Ra 0.4–0.8 µm on designated surfaces
Hardness Reference range: 85–125 HV; final acceptance depends on grade, condition and processing
Electrical Conductivity Minimum value and test method to be specified according to material grade and finished condition
Mounting Features Hole diameter, elongated holes, counterbores, spacing and end slit according to approved drawings
Surface Options Bare copper, brushed finish, specified anti-tarnish treatment, or optional silver, tin or nickel plating
Optional Silver Thickness Reference range: 5–30 µm, with plated areas and coating requirements defined by order
Material Standard ASTM B187/B187M for applicable bar or busbar stock; ASTM B152/B152M for applicable plate stock, or another agreed specification
Supply Basis Customer-approved drawing, confirmed material specification and agreed inspection requirements

Product Detail

Product Tags

Video

Short Description

Cymber Metal supplies custom L-bent slotted copper busbar connectors for drawing-defined electrical connections. The photographed design features four longitudinal through-slots forming five ribs across the bend, a rounded flat mounting end, and a split upright mounting end.

Material grade, arm dimensions, bend radius, slot geometry, mounting holes and surface treatment can be specified for the application. C11000, C10200 and C10100 copper options can be reviewed according to conductivity, forming and documentation requirements.

Product Overview

An L-bent slotted copper busbar connector provides an angled conductive connection between mounting interfaces. Its geometry combines a bent copper body with longitudinal openings and drilled terminal pads.

The illustrated component has four long slots extending across the curved section, dividing that region into five ribs connected at both ends. One mounting end has a rounded outline and two holes. The opposite end includes two mounting holes separated by a central end slit.

This configuration can be evaluated for switchgear, power conversion equipment, transformer connections and other custom busbar assemblies. Slot dimensions, remaining copper cross-section, joint contact area and mechanical loading must be considered together when developing the design.

Material selection can start with Cymber Metal’spure copper materials. Drawing-defined slots, mounting interfaces and finishing requirements can be reviewed through ourcopper machining support.

Current capacity, temperature rise and electrical withstand performance depend on the complete installed assembly. These characteristics cannot be established from the component’s appearance alone.

Key Features

Feature Design Detail / Buyer Benefit
L-Bent Geometry Provides an angled connection between two mounting interfaces. Arm lengths, bend radius and interface orientation can be drawing-defined.
Four-Slot, Five-Rib Layout Divides the bent section into parallel ribs while retaining connected terminal regions at both ends.
Openings Across the Bend Creates open passages through the curved region. Any cooling benefit depends on enclosure conditions, airflow and thermal validation.
Split Mounting End Includes a central slit between the two end mounting areas. Its effect on seating and deformation depends on geometry and bolt loading.
Two-Hole Mounting Interfaces Supports drawing-defined bolted connections at both ends. Hole geometry and spacing must match the mating assembly.
Rounded External Outline Provides a rounded terminal outline and edge transitions; specified edge radii can be included in the drawing.
Defined Contact Surfaces Contact pad flatness, roughness and coating can be controlled separately from non-contact surfaces.
Material and Finish Options Allows material condition and surface treatment to be selected for the electrical, mechanical and environmental requirements.

Manufacturing Process

A practical manufacturing route for this geometry is to form the copper blank before machining the long slots. The final sequence, tooling and machining method should be confirmed during drawing review.

Stage Process Main Control Points
Drawing Review Review the 2D drawing, 3D model and mating interfaces. Material grade, arm dimensions, bend radius, slot geometry, datums and contact areas
Material Preparation Select and cut suitable copper stock. Material identification, thickness, condition and machining allowance
Controlled Bending Form the blank using suitable tooling and a defined bend radius. Bend angle, local thinning, distortion and visible surface defects
Slot Machining Machine the longitudinal slots using suitable CNC equipment and workholding. Slot width, rib thickness, spacing, tool access and support of the bent section
Terminal Machining Finish mounting pads, holes, end slit and other drawing-defined details. Hole position, pad geometry, contact-face condition and datum relationships
Edge Finishing Remove burrs and finish specified edges. Slot ends, hole edges, external radii and cleanliness
Surface Treatment Apply the agreed cleaning, anti-tarnish treatment or plating. Surface preparation, coating coverage, masking and dimensional allowance
Final Inspection Inspect the finished component against agreed requirements. Dimensions, finish, material records and order-specific acceptance criteria

For coating-related requirements, Cymber Metal’sbusbar plating shopprovides relevant service context. Coating type, thickness, adhesion requirements and masked areas should be specified before production.

Manufacturing & Quality Control

Inspection scope, sampling frequency and documentation should be agreed before production. The following items provide a basis for an order-specific quality plan.

Inspection Item Method / Control Approach Acceptance Basis
Material Identification Review material certificates and arrange composition testing where required. Oxygen-related requirements need an appropriate verification method. Ordered grade, material standard and certificate requirements
Electrical Conductivity Use an agreed conductivity or resistivity test method with suitable calibration and temperature control. Specified minimum value for the selected grade and finished condition
Overall Geometry Check arm dimensions, bend angle and mounting interface orientation. Approved drawing and agreed datum system
Slot and Rib Geometry Measure slot width, rib thickness, spacing and relevant feature relationships. Drawing-defined dimensions and tolerances
Mounting Holes Check hole dimensions, position, spacing and any specified counterbores or elongated features. Mating-interface requirements
Contact Pad Condition Check flatness, surface roughness and surface cleanliness. Specified contact area and inspection method
Bend Integrity Conduct visual inspection; arrange additional surface or volumetric testing when specified and technically appropriate. Agreed defect limits and inspection procedure
Hardness Test at agreed locations where hardness is an acceptance requirement. Material condition and drawing requirement
Plating Quality Check coating thickness, coverage, adhesion or other characteristics as specified. Agreed coating specification and test plan
Documentation Arrange material records, dimensional reports and applicable additional certificates. Purchase order requirements; EN 10204 3.1 documentation where applicable and agreed
Assembly Performance Define any required joint-resistance, temperature-rise, dielectric or short-circuit testing at the appropriate assembly level. Applicable equipment standard and customer qualification plan

For further inspection and documentation information, see Cymber Metal’sQuality Assurancepage.

Typical Applications

These are potential application areas for drawing-based evaluation, not prequalified equipment ratings.

Application Potential Component Role Engineering Points to Confirm
Switchgear Busbar Assemblies Angled connection between busbars, terminals or conductive interfaces Current, temperature rise, clearances, contact area and short-circuit forces
Air Circuit Breaker Connections Custom connection between a breaker terminal and the external busbar arrangement Mounting geometry, bolt loading and manufacturer-specific requirements
Converter and Inverter Equipment Angled conductive transition within a power conversion assembly AC/DC duty, frequency content, current distribution and enclosure cooling
Energy Storage Power Conversion Systems Custom busbar connection between equipment interfaces Continuous current, thermal cycling, insulation and installation access
Transformer and Traction Equipment Drawing-defined terminal transition or busbar bracket Mechanical support, vibration, joint integrity and thermal loading
Induction Heating Power Supplies Custom copper connection for a frequency-specific circuit design Skin and proximity effects, net cross-section and validated AC losses

Frequently Asked Questions

What is an L-bent slotted copper busbar connector?

An L-bent slotted copper busbar connector is a copper conductive component with angled mounting interfaces and slots through part of its body. The illustrated version has four longitudinal slots forming five ribs across the bend. It is a custom connection component, not a complete switch or circuit breaker.

Is this a flexible copper connector?

Not necessarily. A slotted solid copper body should not automatically be treated as equivalent to a braided or laminated flexible connector. Any permitted movement, spring response, vibration accommodation or fatigue life must be established from the material, geometry, mounting conditions and testing.

Do the slots increase current capacity or eliminate skin effect?

Not automatically. Slots change the available copper cross-section, exposed surface area and current paths. Depending on frequency and installation conditions, they may also affect AC losses and airflow. Improved ampacity or reduced losses must be demonstrated through suitable calculation, simulation or testing.

Which copper grade should be selected?

C11000 is a common option for electrical copper components. C10200 or C10100 may be specified where oxygen-free material is required. Selection should consider conductivity, forming, temperature and certification needs. Alternative alloys require separate review because their electrical and mechanical properties differ from pure copper.

Can the mounting holes, end slit and bend angle be customized?

Yes, these features can be reviewed against customer drawings. Please specify hole dimensions, elongated-hole or counterbore details, center distances, end-slit geometry, bend angle and mating interfaces. Critical tolerances should reference a clear datum system so manufacturing and inspection use the same basis.

Are the listed dimensions and tolerances guaranteed for every design?

No. The listed figures are references for quotation and feasibility review. Achievable tolerances depend on part size, copper condition, bend geometry, machining access and inspection method. Final acceptance requirements must be confirmed on the approved drawing and purchase order.

Can the connector be silver-, tin- or nickel-plated?

These finishes can be reviewed according to the application. Specify the coating material, thickness, plated contact areas, masking and relevant test requirements. Finish selection should consider mating materials, temperature and environment. Plating alone does not establish the assembled joint’s resistance or service life.

Is the connector certified to IEC 61439 or IEC 62271-1?

A standalone connector should not be described as certified to these equipment standards without supporting evidence. Relevant requirements may form part of the complete assembly’s qualification. Specify the equipment type, applicable standard and required test evidence so the component’s role can be evaluated correctly.

Request a Quote

To request a quotation for a custom L-bent copper connector, please provide the following information.

Required Information Details to Include
Drawing / Model Dimensioned PDF drawing and STEP or another agreed 3D format
Material Copper grade, material standard and required condition
Main Dimensions Arm lengths, width, thickness, bend radius and bend angle
Slots and Ribs Slot count, width, length, end radius, spacing and minimum rib thickness
Mounting Interfaces Hole dimensions, hole positions, end slit, contact areas and mating details
Critical Tolerances Datum system, hole position, flatness, angular tolerance and surface roughness
Electrical Conditions AC/DC, operating current, frequency, temperature limits and relevant assembly requirements
Surface Treatment Bare copper or specified plating, thickness and masking
Quantity Prototype quantity, batch quantity and estimated annual demand
Inspection Documents Material certificate, dimensional report, coating report or third-party inspection requirements
Delivery Requirements Destination, packaging needs and requested delivery schedule

Contact Cymber Metal for a drawing-based quotation. Send your drawings and operating requirements so we can review material selection, processing feasibility, inspection scope and surface treatment.


  • Previous:
  • Next:

  • Write your message here and send it to us