Cold-Drawn Compact Double-Rabbet Z-Section Pure Copper Terminal Block

Short Description:

Item Specification
Product Type Compact double-rabbet Z-section pure copper terminal block or busbar jumper
Material Options C11000, C10200, C10100, Cu-ETP, Cu-OF, T2, TU1, TU2
Optional Materials C10400, C10700, or C18150 may be reviewed separately for specific thermal, wear, or softening-resistance requirements
Applicable Standards ASTM, EN, JIS, GB/T, or customer drawing, depending on grade and product form
Section Configuration Symmetrical double-rabbet Z-profile or asymmetric offset-rabbet configuration
Overall Width Indicative enquiry range: 8–160 mm
Overall Height Indicative enquiry range: 6–120 mm
Rabbet or Step Depth Approximately 1.5–50 mm, subject to section design
Cut Block Length Approximately 8–800 mm
Straight Bar Length Approximately 1,000–6,000 mm
Coil Supply Possible only when section size, temper, and forming feasibility allow
Step Thickness Tolerance Indicative target: ±0.015–0.04 mm
Step Height Difference Confirmed by drawing and inspection method
Four-Plane Parallelism Indicative target: ≤0.02 mm
Rabbet Wall Verticality Indicative target: ≤0.02 mm
Root Radius Approximately R0.15–0.30 mm when feasible
Surface Roughness Indicative target: Ra 0.4–0.8 μm
Temper H02, H04, or O60 according to forming and assembly requirements
Hardness Indicative range for selected hard tempers: approximately 85–125 HV
Conductivity Confirmed by grade, temper, standard, and test method; high-conductivity copper grades may be specified for electrical use
Surface Finish Bright copper, cleaned copper, anti-tarnish treatment, silver plating, tin plating, or nickel plating
Secondary Operations Cutting, drilling, tapping, milling, deburring, slotting, brazing, and plating
Inspection Documents Dimensional report, material certificate, conductivity or hardness report, and additional documents when required
Customization 2D drawing, 3D model, sample, or detailed section sketch accepted for review

Product Detail

Product Tags

Video

Short Description

The double-rabbet Z-section copper terminal block is a compact custom copper profile designed for offset electrical connections, internal busbar transitions, and interlocking contact assemblies.

Its upper and lower flanges extend in opposite directions, creating a stepped Z-section with a thick central conductive body. This geometry can help connect conductors positioned at different elevations while maintaining a short installation span. The two rabbet steps can also be designed to engage with a matching slot, base, or mating copper bar.

The profile can be produced from C11000, C10200, C10100, Cu-ETP, Cu-OF, T2, TU1, or TU2 copper, subject to the required standard, temper, conductivity, and production route. Optional secondary operations include cutting, drilling, tapping, deburring, silver plating, tin plating, nickel plating, and CNC finishing.

Dimensions, tolerances, surface finish, conductivity, and final application suitability are confirmed against the customer drawing and operating conditions.

Product Overview

This compact double-rabbet Z-section copper terminal block is intended for applications where a standard flat busbar or bent copper strip cannot provide the required elevation change, short-span transition, or mechanical positioning.

The profile includes:

  • Upper and lower flanges projecting in opposite directions
  • A central current-carrying section
  • Two stepped rabbet surfaces
  • Compact elevation offset within a short overall length
  • Potential keyed orientation when used with a matching mating slot
  • Custom cut lengths and secondary machining options
  • Optional plating for contact, corrosion, or assembly requirements

Compared with a conventional bent busbar, a drawn profile can provide a more repeatable cross-section for compact applications. Compared with machining the complete geometry from solid bar, profile forming can reduce material removal and simplify repeat production. The final route depends on section size, copper grade, temper, quantity, tolerance, and annual demand.

For standard material options, see Cymber Metal’sPure Copperproduct range. For complex section geometry, theCustom Copper Profile Extrusionservice can be reviewed. Drilling, tapping, cutting, and finished component work can be discussed throughFine Machining.

Key Features

Feature Buyer Value
Compact Z-section geometry Supports short-span connections between conductors at different elevations
Opposite double-rabbet steps Allows a designed mating bar, slot, or base to engage from two directions
Thick central conductive body Provides a stable current path within a compact profile
Custom section design Width, height, step depth, flange position, and root radius can be reviewed to drawing
Cold-drawn profile option Suitable for repeatable section geometry when the cross-section and quantity support drawing
Cut-to-length supply Reduces additional saw-cutting work during assembly
CNC secondary processing Holes, threads, slots, chamfers, and contact surfaces can be added where required
Plating options Silver, tin, or nickel plating can be reviewed for contact and environmental requirements
Multiple copper grades Material can be selected according to conductivity, formability, strength, and thermal requirements
Drawing-based quality control Critical geometry is inspected against defined datums and customer tolerances
Traceable production route Heat, lot, forming, cutting, machining, and inspection records can be organized according to order requirements
Application flexibility Suitable for prototype review, replacement parts, and repeat OEM production after approval

Manufacturing & Quality Control

Manufacturing Process

Process Stage Description Output or Control Focus
Engineering Review The section drawing, mating components, current path, operating temperature, and assembly direction are reviewed before production. Confirm section feasibility, datum structure, and critical dimensions
Material Selection Copper grade and temper are selected according to conductivity, formability, hardness, plating, and application requirements. Grade and temper confirmed by quotation or technical approval
Billet or Feedstock Preparation Suitable copper feedstock is prepared according to the selected production route. Heat or lot identification maintained
Profile Forming Where technically suitable, extrusion and controlled cold drawing are used to form the Z-section and rabbet geometry. Cross-section, step position, and surface condition controlled
Straightening The formed profile is straightened to meet the agreed camber or straightness requirement. Straightness checked over the specified measuring length
Cutting Precision sawing produces cut blocks or fixed-length bars. Length, squareness, and burr condition inspected
CNC Secondary Machining Holes, slots, threads, chamfers, contact faces, or other features are added when required. Critical features inspected against drawing datums
Surface Treatment Cleaning, anti-tarnish treatment, silver plating, tin plating, or nickel plating may be arranged according to the application. Coating specification and coverage confirmed when applicable
Final Cleaning Parts are cleaned and protected for packing and shipment. Loose chips, excessive burrs, and contamination removed
Packaging Components are packed with protective separation and moisture-control measures where appropriate. Prevent deformation, scratching, and oxidation during transport

Quality Control System

Quality Control Item Inspection Method Notes
Chemical Composition Supplier certificate and appropriate material analysis Exact method depends on grade and order standard
Material Identification Heat number, lot number, and production record review Traceability can be maintained through the production route
Section Dimensions Calipers, micrometers, profile projector, optical measurement, or CMM Critical width, height, step, and flange dimensions checked
Step Thickness and Height Dedicated gauges, optical measurement, or CMM Measurement datums must be defined on the drawing
Parallelism CMM, optical measuring system, or controlled gauge inspection Four-plane parallelism is confirmed only when specified
Rabbet Wall Angle Profile measurement or CMM 90° geometry is subject to drawing tolerance
Straightness and Camber Straightedge, gauge table, or coordinate measurement Measuring span and acceptance criteria must be agreed
Surface Roughness Profilometer when required Ra target depends on forming and finishing route
Hardness Vickers or other agreed hardness method Temper and test location are confirmed before inspection
Electrical Conductivity Eddy-current conductivity meter or laboratory method Grade, temperature, and test standard affect the result
Burrs and Edge Condition Visual inspection and dimensional check Deburring requirements should be defined for assembly safety
Plating Thickness Coating thickness measurement when plating is ordered Plating type, coverage, and thickness are confirmed separately
Functional Fit Sample assembly or go/no-go gauge Recommended for mating slots, rabbet joints, and contact bases
Final Documentation Dimensional report, material certificate, and agreed inspection records Third-party inspection can be discussed for qualifying orders

For current quality documentation and inspection support, see theQuality Assurancepage. Certificate type, inspection scope, and document availability should be confirmed for each order.

Typical Applications

Application Typical Use Design Considerations
Molded-Case Circuit Breakers Internal offset bridge or compact conductor connection Confirm current, temperature rise, insulation clearance, and assembly direction
Switchgear Assemblies Stepped terminal or internal busbar transition Check mating bars, creepage distance, short-circuit forces, and enclosure space
DC Contactors Compact conductive base or jumper between offset terminals Review contact resistance, plating, thermal cycling, and fastening method
High-Power Relays Fixed copper contact support or offset connection Confirm contact pressure, electrical duty cycle, and wear conditions
Laminated Busbar Systems Elevation transition between conductor layers Verify insulation system, clearances, and tolerance stack-up
EV Battery Packs Compact internal copper bridge or terminal interface Review current, vibration, heat dissipation, and insulation requirements
Power Inverters Internal conductor transition or terminal support Confirm thermal path, mounting method, and electrical spacing
Distribution Panels Custom copper connection between offset components Specify hole pattern, cut length, plating, and installation sequence
Transformer and Generator Components Custom conductive connection or support part Confirm temperature, vibration, electromagnetic loading, and joining method
Custom Electrical Equipment OEM-specific stepped copper profile A drawing, prototype, or mating sample is recommended before batch production

Application suitability must be confirmed by the equipment designer. The product page does not replace electrical, thermal, mechanical, or safety validation at the equipment level.

FAQ

What is a double-rabbet Z-section copper terminal block?

It is a compact copper profile with upper and lower steps extending in opposite directions. The geometry is used for offset conductor connections, compact busbar transitions, and mating assemblies that require controlled positioning.

Which copper grades are available?

Common options include C11000, C10200, C10100, Cu-ETP, Cu-OF, T2, TU1, and TU2. The final grade should be selected according to conductivity, forming route, temper, standard, and application requirements.

Can the profile be produced as a custom cross-section?

Yes. Width, height, flange position, rabbet depth, root radius, cut length, holes, slots, and other features can be reviewed from a 2D drawing, 3D model, or sample.

Is this product cold drawn or machined?

The basic profile may be produced by extrusion and controlled cold drawing when the section and quantity are suitable. CNC machining can be added for holes, slots, threads, contact faces, or low-volume prototypes.

Can silver plating or tin plating be added?

Optional silver, tin, or nickel plating can be reviewed. The plating type, thickness, coverage, base material, and contact requirements should be specified in the drawing or RFQ.

What tolerances can be achieved?

The source design includes indicative targets such as ±0.015–0.04 mm for selected step dimensions and ≤0.02 mm for selected parallelism features. Final tolerances depend on section geometry, length, temper, process, and inspection method.

Can the parts be supplied in short cut lengths?

Yes. Cut blocks and fixed-length pieces can be discussed. The quotation should specify cut length, quantity, squareness, burr limits, packaging, and whether secondary machining is required.

What information is needed for a quotation?

Please provide the copper grade or preferred conductivity, section drawing, dimensions, tolerance, length, quantity, temper, surface finish, plating, application, inspection documents, destination, and required delivery schedule.

Request a Quote

Required Information Details to Provide
Material Preferred grade such as C11000, C10200, C10100, Cu-ETP, Cu-OF, T2, TU1, or TU2
Standard ASTM, EN, JIS, GB/T, IEC, or customer specification
Profile Drawing 2D drawing, 3D model, section sketch, or physical sample
Dimensions Overall width, height, rabbet depth, step thickness, root radius, and critical datums
Length Cut-block length, straight-bar length, or coil requirement
Quantity Prototype, sample, trial batch, monthly demand, and annual forecast if available
Temper H02, H04, O60, or required hardness and forming condition
Surface Bright copper, cleaned copper, anti-tarnish, silver, tin, or nickel plating
Secondary Operations Holes, slots, threads, chamfers, milling, brazing, or deburring
Application Breaker, switchgear, contactor, relay, EV, inverter, busway, or other equipment
Quality Documents Material certificate, dimensional report, conductivity report, hardness report, RoHS, REACH, or third-party inspection
Delivery Destination country, preferred Incoterm, packing requirement, and target schedule

For a drawing-based quotation, contactCymber Metal.


  • Previous:
  • Next:

  • Write your message here and send it to us