Custom 3D-Bent Copper Tubular Busbar

Short Description:

Parameter Reference Specification / Confirmation Requirement
Product Form Bent copper tubular conductor with cylindrical and flat terminal interfaces
Material Options for Review C11000, C10200 or C10100; grade, standard and temper to be agreed
Tube Outside Diameter Reference range: 12–120 mm
Tube Wall Thickness Reference range: 2–20 mm
Developed Length Reference range: 100–3,500 mm; distinct from overall installed dimensions
Bend Configuration Drawing-defined bend angles, radii, offsets and terminal orientation
Cylindrical End Stepped diameter as shown; additional grooves or threads only when specified
Flat Terminal Palm Two mounting holes as shown; outline, thickness and hole spacing by drawing
End-to-End Position Reference coordinate deviation: ±0.2–0.5 mm, subject to agreed datums and measurement method
Machined End Diameter Reference tolerance: ±0.02 mm, subject to feature and process review
Palm Contact Flatness Reference target: ≤0.03 mm over the specified contact area
Contact Surface Roughness Reference target: Ra 0.4–0.8 μm on designated surfaces
Conductivity Acceptance value and test method to be agreed for the selected material
Surface Treatment Copper finish, silver/tin/nickel plating or selective insulation, subject to review
Material Documentation Certificate type, traceability and inspection scope agreed before ordering

Product Detail

Product Tags

Video

Short Description

Custom copper tubular busbar combining a spatially bent body, a stepped cylindrical connection end and a two-hole flat terminal palm. The round-to-flat configuration provides a transition between cylindrical interfaces and bolted flat connections. Material grade, bend geometry, terminal dimensions, surface treatment and inspection requirements are specified by drawing for switchgear, transformer and industrial electrical projects.

Product Overview

A copper tubular busbaris an electrical conductor with a hollow tubular body. In this round-to-flat design, the bent body routes the conductor around surrounding equipment, while the flat terminal palm provides a bolted connection interface.

The photographed component shows a stepped cylindrical end, multiple bends and a flat terminal with two mounting holes. Bore dimensions, wall thickness, material grade and manufacturing route require drawing or production-record confirmation.

Cymber Metal can support material selection through itspure copper product rangeand drawing-based interface development through itscopper machining support. Final design review should consider terminal alignment, assembly access, contact pressure, temperature rise and electrical insulation requirements.

Key Features

Feature Design Purpose / Buyer Consideration
Round-to-Flat Transition Connects a tubular conductor body to a flat bolted interface
Spatially Bent Body Accommodates drawing-defined routing and terminal offsets
Stepped Cylindrical End Provides a defined mating diameter where required by the assembly
Two-Hole Terminal Palm Provides two fastening locations; rotational restraint depends on the complete joint design
Defined Contact Surface Allows flatness, roughness and plating requirements to be specified
Custom Terminal Orientation Aligns the round and flat interfaces with the mating equipment
Selective Finishing Allows contact zones and non-contact areas to receive different treatments when specified

Silver, tin or nickel finishing can be reviewed through Cymber Metal’sbusbar plating support. Coating thickness, coverage, adhesion and dimensional allowance must be defined for the order.

Manufacturing Process

The production route should be agreed after reviewing the material, tube section, bends and terminal design.

Stage Process Considerations
Drawing and Material Review Confirm grade, temper, tube dimensions, terminal datums and functional requirements
Blank Preparation Prepare the specified tube stock and cutting allowance
Conditioning and Bending Review annealing needs and bending method to control springback, ovality and wall thinning
Round-to-Flat End Forming Develop the palm transition with controlled thickness, width and bend geometry
Interface Machining Finish specified diameters, contact faces, holes and edge details using suitable fixtures
Surface Treatment Apply the agreed cleaning, plating or insulation process
Final Inspection and Packing Verify drawing requirements and protect contact surfaces during shipment

An integral flattened-tube design must be distinguished from a separately joined terminal. Flattening alone does not establish metallurgical bonding between the opposing tube walls.

Manufacturing & Quality Control

Inspection methods, sampling frequency and acceptance limits should form part of the agreed inspection plan.

Control Area Inspection / Verification
Material Identity Review material certificates and perform supplementary verification when specified
Oxygen-Free Grade Requirements Confirm oxygen-related requirements using appropriate certification or testing; appearance is not proof
Tube Section Check outside diameter, wall thickness and accessible bore dimensions
Bend Quality Evaluate bend radius, ovality, wall thinning and visible surface defects
Spatial Geometry Measure terminal positions and orientation against agreed datums
Palm and Mounting Holes Check palm thickness, hole diameter, spacing, edge distance and terminal angle
Contact Surfaces Verify specified flatness, roughness and surface condition
Formed-Zone Integrity Use visual inspection and, where technically suitable and agreed, additional nondestructive testing
Electrical Properties Perform conductivity or resistance testing when required by the order
Coating and Documentation Verify specified coating requirements and supply the agreed inspection records

Cymber Metal’squality certification informationcan support supplier-document review. Current certificates, EN 10204 3.1 documentation where applicable, and special inspection reports should be confirmed before ordering.

Typical Applications

These are potential application contexts, not automatic equipment approvals or voltage ratings.

Application Typical Connection Role Design Checks
Switchgear and Ring Main Units Shaped internal connection between offset terminals Temperature rise, assembly access, insulation clearances and fault-current forces
Gas-Insulated Equipment Drawing-specific round-to-flat internal conductor Electric-field design, dielectric performance, partial discharge and equipment qualification
Transformer Connections Transition between cylindrical and flat terminal interfaces Contact pressure, mechanical support, thermal loading and terminal alignment
Inverters and Industrial Power Electronics Spatially routed electrical link within an enclosure Current waveform, frequency, temperature, insulation and fastening requirements
Induction Heating Equipment Custom electrical connection between power components Duty cycle, current distribution and cooling arrangements; no pressure rating implied

Frequently Asked Questions

What is a copper tubular busbar?

A copper tubular busbar is an electrical conductor with a hollow tube section. This version combines a bent body with cylindrical and flat connection interfaces. Its current-carrying capability depends on the conducting cross-section, material, operating frequency, cooling conditions, joint design and permitted temperature rise.

How does this differ from a solid copper busbar?

A tubular busbar has a hollow section, while a solid busbar has a fully filled cross-section. Neither is automatically superior. Selection should consider available space, electrical loading, mechanical support, forming requirements and connection geometry. The tube’s external diameter alone does not establish its electrical capacity.

Which copper grades can be considered?

C11000, C10200 and C10100 can be reviewed against the project requirements. Selection should account for conductivity, forming operations, joining conditions and documentation needs. The required grade, standard and temper must be stated explicitly; designations from different standards should not be assumed equivalent without checking their requirements.

Can the bends and terminal dimensions be customized?

Drawing-defined bend radii, offsets, terminal angles, stepped diameters and hole patterns can be reviewed. Feasibility depends on tube diameter, wall thickness, material condition, tooling access and inspection requirements. A 3D model together with a dimensioned 2D drawing helps define both the routing envelope and critical connection interfaces.

Is the round-to-flat transition necessarily weld-free?

No. The construction must be confirmed from the approved manufacturing route. An integral formed-tube design differs from a tube fitted with a separately welded or brazed terminal. Photographs alone cannot verify the absence of joints, internal defects or the degree of bonding within a flattened tube end.

Are silver plating and insulation available?

Silver, tin or nickel plating and selected insulation treatments can be reviewed for the project. Specify the treatment areas, coating thickness, masking boundaries and inspection requirements. Insulation thickness or material alone does not establish a complete assembly’s voltage rating, creepage distance or clearance compliance.

Does this product have a fixed current or voltage rating?

No fixed rating should be assigned from these photographs or reference dimensions. Current capacity requires thermal evaluation, while voltage suitability depends on the complete insulation and equipment design. High-voltage applications may also require electric-field analysis, partial-discharge assessment and equipment-level testing.

What information is needed for a quotation?

Provide the material specification, drawings, quantity, tube dimensions, bend geometry, terminal interfaces, tolerances and surface treatment. Include operating current, AC/DC conditions, frequency, insulation requirements and required documents. State the delivery destination and target schedule so feasibility, inspection scope and delivery planning can be reviewed together.

Request a Quote

Required Information Details to Provide
Drawings Dimensioned PDF and available STEP or other 3D model
Material Grade, standard, temper and required electrical properties
Tube Geometry Outside diameter, wall thickness and developed length
Bend Layout Radii, angles, offsets, routing envelope and terminal orientation
Connection Interfaces Stepped diameters, palm dimensions, hole pattern and mating components
Critical Requirements Datums, tolerances, contact flatness and roughness
Operating Conditions Current, AC/DC, frequency, temperature and installation environment
Surface Treatment Plating, insulation, coverage boundaries and thickness
Quantity Sample quantity, batch quantity and expected annual demand
Inspection Documents Material certificate, dimensional report and any special testing
Delivery Destination, packing requirements and target schedule

Contact Cymber Metal for a drawing-based quotation.


  • Previous:
  • Next:

  • Write your message here and send it to us